Carburetor Removal

Drain the coolant (page 6-5).

Remove the air cleaner housing (page 5-14).

California type Disconnect the No. 11 tube. only:

California type Disconnect the No. 5 tubes. only:

Honda Cbr 600 Del 2000Cbr 600 Carburetor

Remove the choke cable from the cable holder and disconnect it from the starting enrichment (SE) valve arm.

CHOKEfffiABLE

Romovo tho throttle otop ocrcw from the holder.

"HROTTLE STOP SCREW '

"HROTTLE STOP SCREW '

Loosen the four carburetor insulator band screws at the engine side, using a long screwdriver through the hole in both sides of the frame.
1997 Honda Cbr With Arm Extentions

Place a clean shop Remove the carburetor assembly off the cylinder towel over the head intake ports. intake ports to prevent any Disconnect the throttle sensor connector. foreign material from dropping into NOTE'

Do not remove the throttle sensor unless it is necessary to replace it or disassemble the carburetor. For sensor inspection and replacement, see page 17-7.

Loosen the throttle cable lock nuts, then remove the cables from the cable holder and disconnect them from the throttle drum.

Honda Throttle Cable Removal

Disconnect the water tubes from the carburetor.

Xjr400 Carburettor Diagram

CARBURETOR SEPARATION

NOTE:

The vacuum chamber and float chamber can be serviced without separating the carburetors.

Remove the following:

— throttle stop screw with spring and washer

— carburetor insulators by loosing band screws —two screws and washers

— SE valve arm and return spring —two collars

SEHA^VE ARM

SCREWS/WASHERS

SEHA^VE ARM

SCREWS/WASHERS

The vacuum chamber and float chamber can be serviced without separating the carburetors.

1995 Cbr Throttle Cable

THROTTLE STOP SCREW

INSULATORS

THROTTLE STOP SCREW

INSULATORS

—front connecting nut, screw and throttle sensor.

CAUTION:_

Do not remove the throttle sensor from the bracket unless it requires replacement. It may cause the sensor to move out of position resulting in improper ignition timing.

— connecting nut, bolt and joint retainer -air vent hose joint with O-ring

Cbr Air Vacuum Diagram

-screw and throttle cable holder (joint retainer) -dowel pin

-air vent hose joint with O-ring.

HOSE JOINT

HOSE JOINT

Loosen the synchronization adjusting screws to reduce the spring tension and remove the synchronization springs.

Loosen the synchronization adjusting screws to reduce the spring tension and remove the synchronization springs.

Xtz 750 Synchronization Bandit 600 Carburetter Diagrahm

Remove the dowel pins.

Bandit 250cc Carburetor Diagram

Refer to diagram Separate the No. 1 and No. 2 carburetors then re-onpage 5-26 for move the thrust spring. identification of Remove the following: each component, —joint collar

— water tube joint

Gsf600 Hose Diagram

Separate the No. 3 and No. 4 carburetors then remove the thrust spring. Remove the following:

— choke cable holder —joint collar —fuel tube joint

Bandit 600 Carburetter Diagrahm
0 0

Responses

  • richard
    How to clean carb on cbr 600?
    8 years ago
  • isengrin
    How do i remove the carburetors on a 2000 honda cbr?
    8 years ago
  • rezene
    How to clean carbs on CBR 600?
    7 years ago
  • senay abaalom
    How to remove carbs on a honda cbr 660 2000?
    7 years ago
  • mimosa
    How to replace a carburetor on honda hrt 163?
    7 years ago
  • pauliina
    How to remove fuel carbs for cbr 600 1991?
    6 years ago
  • janie
    Where to fit a throttle stop screw cbr 600 1994?
    6 years ago
  • amanda
    How ro remove carb on honda cbr 600 2000?
    6 years ago
  • marco
    How to remove carbs on a 1996 honda cbr600?
    6 years ago
  • ERMIAS SIMON
    How long does it take to remove the carburetors from a 2000 cbr600?
    6 years ago

Post a comment