Instrument Functions

COMBINATION METER

® Speedometer (2 Clock, odometer (3 Select button @ Reset button

This combination meter is equipped with the following.

• Two trip odometers

Odometer and trip meters

Use the trip meters to estimate how far you can ride on a tank of fuel.

Push the Select button to change between the odometer mode "ODO" and the trip odometer modes "TRIP 1" and "TRIP 2" in the following order:

"ODO" ^ "TRIP 1" ^ "TRIP 2" ^ "ODO" To reset a trip odometer to 0.0, select it by pushing the select button and push the reset button for at least one second.

Clock

To change the display to the clock mode, push both the select and reset buttons. To set the clock:

1. Push both the select and reset buttons for at least two seconds.

2. When the hour digits start flashing, push the reset button to set the hours.

3. Push the select button to change the minutes.

4. When the minute digits start flashing, push the reset button to set the minutes.

5. Push the select button to start the clock.

After setting the clock, be sure to push the select button before turning the main switch to "OFF", otherwise the clock will not be set.

SIGNAL SYSTEM

CIRCUIT DIAGRAM

EB806000

(3 Main switch

(4 Fuse (position light and hazard) © Battery (8 Main fuse

Fuel sender @ Fuel meter @ Fuel level indicator light @ Turn indicator light (left)

33 Turn indicator light (right)

34 Speed meter

35 Speed sensor

36 Front flasher light

37 Rear flasher light

44 Hazard switch

45 Turn switch @ Flasher relay

Hazard relay

TROUBLESHOOTING

* Any of the following fail to light: flasher light, trun and fuel level indicator light.

* The fuel meter fails to operate.

Check:

1. main and signal system fuses

2. battery

3. main switch

4. wiring

(of the entire signal system)

* Before troubleshooting, remove the following part(-s):

1) seats

2) fuel tank

3) air filter case

4) side cowlings

5) side covers

* Troubleshoot with the following special tool(-s).

Pocket tester 90890-03112

Pocket tester 90890-03112

1. Main and signal system fuses

■ Check the main and signaling system fuses for continuity.

Refer to "FUSE INSPECTION". > Are the main and signaling system fuses OK?

Replace the fuse(-s).

2. Battery

1 Check the condition of the battery. Refer to "BATTERY INSPECTION".

Open-circuit voltage 12.8 V or more at 20°C

Clean the battery terminals.

• Recharge or replace the battery.

EB806400

4. Wiring

1 Check the entire signal system's wiring. Refer to "CIRCUIT DIAGRAM". 1 Is the signal system's wiring properly connected and withour defects?

^ YES ^ NO

Check the condition of each of the signaling system's circuits. Refer to "SIGNAL SISTEM CHECK."

Properly connect or repair the signal system's wiring

EB802401

B802400

EB806400

SIGNAL SYSTEM CHECK

1. Flasher light and/or turn indicator light does not blink.

1. Flasher/turn indicator light bulb and socket

► Check the flasher/turn indicator light bulb and socket for continuity.

►Are the flasher/turn indicator light bulb and socket OK?

Replace the flasher/turn indicator light balb, socket or both.

2. Turn switch

» Refer to "SWITCH INSPECTION".

Replace the left handlebar switch.

3. Voltage

►Connect the pocket tester (DC 20 V) to the hazard relay coupler.

Tester (+) lead ^ Brown/Red terminal ® Tester (-) lead ^ Frame ground

►Turn the main switch to "ON" or "P".

► Check for voltage (12 V) on the "Brouwn/Red" lead at the flasher relay terminal.

► Is the voltage within specification.

Wiring circuit from main switch to hazard relay connector is faulty, repair.

4. Voltage

Connect the pocket tester (DC 20 V) to the flasher relay coupler.

Tester (+) lead ^ Brown/Red terminal © Tester (-) lead ^ Frame ground

►Turn the main switch to "ON" or "P". ►Check for voltage (12 V) on the "Brown/Red" lead at the flasher relay terminal. ► Is the voltage within specification.

Wiring circuit from main switch to flasher relay connector is faulty, repair.

5. Voltage

Connect the pocket tester (DC 20 V) to the flasher relay lead.

Tester (+) lead ^ Brown/White terminal ® Tester (-) lead ^ Frame ground

• Turn the main switch to "ON" or "P".

• Check for voltage (12 V) on the "Brouwn/White" lead at the flasher relay terminal.

• Is the voltage within specification.

Replace the flasher relay.

5. Voltage

Connect the pocket tester (DC 20 V) to the bulb socket connector.

Flasher lights Turn indicator light

At flasher light (left):

Tester (+) lead ^ Chocolate lead ® Tester (-) lead ^ Frame ground

At flasher light (right):

Tester (+) lead ^ Dark green lead ( Tester (-) lead ^ Frame ground

Was this article helpful?

0 0

Post a comment