Lubrication Diagrams

© Camshaft (intake) (2 Camshaft (exhaust) (3 Main gallery © Oil strainer (5 Oil pump (6 Main axle © Crankshaft

Yamaha 600 1991 Oil Place

© Oil cooler © Starter clutch © Main axle @ Drive axle © Oil pump © Oil pan © Relief valve © Main gallery

Xjr 1300 Clutch

© Camshaft © Crankshaft © Oil pump © Oil filter

Xjr 1300 Wiring Diagram

CABLE ROUTING

0 Starter motor cable

®

Throttle position sensor

[A Fasten the wireharness to the

(2 Battery negative (-) lead

©

Ignition coil lead (#2, 3)

seat rail with a plastic band. Make

© Battery negative (-) lead con

©

Throttle cable

sure that the end of band down

nector

©

Engine ground lead

ward.

@ AC generator connector

© ©

Air ventilation hose

IB Align the white tape on the wire-

© Rear brake switch lead connec-

Rear brake switch

harness with a plastic band and

tor

©

Starting circuit cutoff relay

fasten them to the seat real.

© Neutral lead

Make sure that the end of band

© Pickup lead

down ward.

® Sidestand switch lead

[C Fasten the wireharness with the

steel clamp on the frame.

Route the wireharness and starter motor cable in front of the reservoir tank bracket and the battery negative (-) lead behind the reservoir tank bracket. And fasten them with a plastic band. Fasten the wireharness, neutral lead, sidestand switch lead, pickup coil lead, AC generator lead and rear brake switch lead to the frame with a plastic band. Make sure that the end of band forward of motorcycle.

[0 Fasten the wireharness to the frame with a plastic band. Make sure that the end of band down ward.

[G Insert the plastic band through the hole of plastic panel and then fasten the throttle cables with it. Make sure that the end of band inside of motorcycle.

[H Fasten the wireharness to the frame with a plastic band. Make sure that the end of band down ward.

|T| Fasten the high tension cables and throttle cables with a plastic clamp.

J Route the air ventilation hoses, air filter case drain hose, fuel tank drain hose and fuel tank breather hose through the engine guide.

IK Fasten the AC generator lead, pick-up coil lead, sidestand switch lead and starter motor cable with a plastic band.

Wiring Diagram For Bad Boy Horn

[L Route the wireharness and starter motor cable behind the side cover bracket and fasten them with a plastic band at front of the bracket.

[M| Align the white paint marks of the fuel tank drain hose, fuel tank breather hose and air filter case drain hose.

M Touch the brake pipe to the brake caliper stopper.

Clutch Xjr 1300

© Clutch hose © Starter cable © Air filter case drain hose © Frame ground © Flasher relay connector © Oil light relay connector © Igniter unit connectors © Starter motor ©AC generator 10 Sidestand switch © Sidestand switch lead 12 Ignition coil lead (#1, 4)

[A Insert the plastic band through the hole of plastic panel and then fasten the clutch hose with it. Make sure that the end of band inside of motorcycle.

[B To headlight lower hole.

[C Route the wireharness and starter cable through the guide.

ID Connect the ignition lead with white marking tape to the ignition coil (#1, 4).

IE Fasten the high tension cables (#1, 2) with a plastic clamp. Position the clamp at 50 - 80 mm above the high tension cable number.

[0 Fasten the horn lead to the frame with a plastic band. Make sure that the end of band down ward.

[G] Install the frame ground and igniter unit together with screw.

Frame Yamaha 1300 Xjr

M Fasten the seat lock cable to the seat real with a plastic band. Make sure that the end of band down ward.

IH Route the air filter case drain hose over the starter motor to right side of motorcycle.

J Position the clutch pipe parallel with the oil filter cover.

IK Fasten the sidestand switch lead with steel clamp on the frame and then route it between the pickup cover, oil filter cover, AC generator and starter motor to the right side of motorcycle.

\H Fasten the clutch hose with steel clamp on the frame.

[M Clamp the gromet on the clutch hose with wire holder on the frame.

[N Route the speedometer cable through the guide.

[O Touch the brake pipe to the brake caliper stopper.

IP Touch the brake pipe to the brake hose joint.

Yamaha Xjr 1300 Drag

0 Throttle cables

12

Starter relay

24 Taillight lead

0 Ignition coil (#2, 3)

Seat lock cable

25 Starter cable

0 Throttle position sensor

Seat lock

0 Neutral switch connector

15

Battery positive (+) lead

[A Position the horn (high) to right

0 Pickup coil connector

16

Fuse box

side.

0 Sidestand switch connector

17

Starter relay connector

IB Fasten the throttle cable (front

0 Battery

18

Flasher relay

side) to the frame with a plastic

0 Reservoir tank

19

Oil light relay

clamp.

0 Battery negative (-) lead

20

Igniter unit

[C Fasten the throttle position sen

10 Starting circuit cutoff relay

21

Fuel sender connector

sor with steel clamp on the car

<11 Battery positive (+) lead connec-

22

Starter cable

buretor (#4).

tor

23

Ignition coil (#1, 4)

[D To fuel sender.

Yamaha Xjr1300 Air Ducting Diagram

[H Connect the fuel sender connector, neutral switch connector, pickup coil connector and side-stand switch connector above the air filter case.

[0 Route the battery negative (-) lead inside of the reservoir tank bracket and under the reservoir tank and then connect it.

[G Fasten the battery positive (+) lead and battery positive (+) lead connector on the groove of the battery with the battery rubber band.

M Position the starter motor cable at 45 degree out side of the motorcycle.

|T| Position the wireharness, tail-light lead and rear turn signal light leads (left and right) between the taillight bracket and rear fender rib.

J Position the seat lock cable inside under the seat lock bracket.

IK Fasten the wireharness to the frame with a plastic band. Make sure that the end of band down ward.

Route the starter cable between the throttle cables.

M Fasten the wireharness, starter cable to the frame with a plastic band. Make sure that end of band down ward.

Xjr 1300 Wiring Diagram

N Fasten the wireharness, taillight lead and rear turn signal light leads (left and right) with steel clamp on the frame make sure that the end of clamp forward.

[O Route the rear turn signal light leads (left and right) through the each holes of the rear fender.

IP Touch the starter cable to the stopper and position it vertical of the motorcyle.

Yamaha Xvz Battery Box Diagram

© Meter leads © Main switch lead © Starter cable @ Handlebar switch lead (left) © Clutch hose © Brake hose

© Handlebar switch lead (right)

[A Route the throttle cables through the guide on the headlight stay.

IB Route the meter leads, main switch lead into the upper hole of the headlight body.

[C Route the handlebar switch lead (left) inside of the clutch hose. Fasten the handlebar switch lead (left), clutch hose and starter cable with a plastic band.

[D Route the handlebar switch lead (left) and front turn signal light lead (left) into the left under hole of the headlight body.

IE Route the front turn signal light leads (left and right) in front of the headlight stay.

F Route the speedometer cable through the guide on the headlight stay.

[G To front brake master cylinder.

Yamaha Xjr Plastic

[0 Touch the brake pipe to the stopper.

IH Route the handlebar switch lead (right) and front turn signal light lead (right) into the right under hole of the headlight stay.

J Fasten the handlebar switch lead (right) and front brake hose with a plastic band.

Xvs1100a Driving Light Bracket
0 -1

Post a comment